Case study · Plastics

Plastic Molding Heat Seal Pins

Over 28% Higher Throughput with Dicronite® Dry Lubrication

A major LCD television manufacturer applied Dicronite dry lubrication to heat seal pins used to bond front cabinet panels. The application delivered a reported throughput increase of over 28%, eliminated resin-removal stoppages, and reduced coating operating costs by more than 50%.

Front cabinet panel 185°C+ Heat seal pin cut away Dicronite® on cavity and sliding surfaces Throughput existing target +25% >28%
Dicronite® filmPlastic stud · throughput
  • >28% Higher throughput Beating the 25% minimum requirement.
  • 0 Resin-removal stoppages Previously two per shift.
  • >50% Lower coating operating costs Compared with the previous coating maintenance.

The challenge

Resin sticking held output below target

Each production jig used 10–15 heat seal pins, depending on panel size. Severe resin sticking caused scrap and production interruptions, leaving output below 50% of the production target.

An initial Teflon coating improved output to approximately 60% of the target, but recurring maintenance remained:

  • Two stoppages per shift to manually remove resin and apply additional mold release agent.
  • Complete pin re-polishing and coating reapplication every two to three weeks, at a reported cost of $7,000.

The manufacturer needed a solution that improved release performance and reduced downtime without changing the pin cavity geometry.

Output against production target

<50%→~60% Uncoated pinsTeflon coating

Before Dicronite dry lubrication.

Teflon still needed two stoppages per shift, and re-polishing and recoating every two to three weeks.

The requirements

Four production objectives

Requirement · production objective

Temperature capability
Continuous operation at or above 185°C
Throughput
At least a 25% increase over the existing process
Dimensional precision
Preserve pin cavity geometry and specifications
Operating costs
Reduce costs associated with coating maintenance and downtime

The Dicronite® solution

Applied to the cavity and sliding surfaces

Dicronite dry lubrication was applied to the cavity and sliding surfaces of the heat seal pins to address resin sticking and improve production performance.

The results

Over 28% higher throughput, beating the 25% target

  • Throughput requirementAt least 25% over the existing process25%required
  • Dicronite-treated heat seal pinsReported throughput increase>28%achieved

Each bar is the throughput increase over the existing process, on a scale of 0 to 40%.

Performance measureReported result
Production throughputIncreased by over 28%
Scrap ratesDecreased
Resin-removal production stoppagesEliminated
Supplemental mold release agent useEliminated
Operating temperatureOperation above 185°C enabled further process optimization
Coating operating costsReduced by more than 50%

The reported throughput improvement exceeded the manufacturer’s minimum 25% requirement. Eliminating recurring resin-removal stoppages and supplemental release agent use also simplified routine production.

The outcome

Adopted into preventive maintenance

Following the results, Dicronite dry lubrication was incorporated into the facility-wide preventive maintenance program.

Contact Dicronite Southwest

Improve your heat seal pin performance

Contact Dicronite Southwest to discuss resin sticking, heat seal pin maintenance, and dry lubrication for your plastic assembly process.

Results reflect the reported application. Performance depends on resin, pin geometry, operating temperature, and production conditions.

Dicronite® Southwest

Request a Dicronite® WS₂ Coating Quote

Send us your project details so we can evaluate your requirements and prepare a quote.

Sending drawings securely

Dicronite® Southwest is CMMC compliant. Please do not attach drawings to this form. Send drawings, including ITAR and CUI technical data, by email to rfq@secure.dicronitesouthwest.com. Email to this secure address is routed into our PreVeil encrypted environment.

Submit this form first so our team can add your email address, or your company's email domain, to the approved list for the secure inbox. Email from addresses that are not on the list cannot be received.

If your company already uses PreVeil, you can also send drawings to us directly through PreVeil.

Email Drawings Securely

Loading the quote form…

Thank you. Your quote request has been received.

Our team will review your project details and follow up by email.